What it means
F2E4 on a Maytag top-load washer is explained as “The F2 E4 alert indicates there is an issue with the user interface or associated wiring.” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
Maytag washer F2E4 / User interface
F2E4 on a Maytag top-load washer is explained as “The F2 E4 alert indicates there is an issue with the user interface or associated wiring.” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
Also printed as F2E4
F2E4 on a Maytag top-load washer is explained as “The F2 E4 alert indicates there is an issue with the user interface or associated wiring.” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
F2E4 returns, or the top-load washer behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

Record F2E4 character by character and note the product type: top-load washer.

Power off for five full minutes, then on, and look for F2E4.

Run the washer briefly after the reset and see whether F2E4 comes back.

Press each key on the top-load washer one at a time and note any that do nothing, beep alone or stick.
Keep the model number close and note when F2E4 appeared and what the top-load washer was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
F2E4 is covered by this wording on the top-load washer page: “The F2 E4 alert indicates there is an issue with the user interface or associated wiring.”
Read the supporting manualLeave the washer off power for five full minutes, switch it back on, and check the display for F2E4.
Read the supporting manualThe top-load washer list prints F2E3 next to F2E4, but with a different line. Look up the one on your display.
Read the supporting manualIf the display jumps or keys misfire, leave the top-load washer off until a technician has looked. Never open a panel on the top-load washer yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13437 / PH 13437 (top-load washer)
Facts for F2E4 are from the top-load washer table (PH 13437) of Maytag Product Help, checked November 2026; no model list is printed.
The top-load washer page reads “The F2 E4 alert indicates there is an issue with the user interface or associated wiring.” It prints nothing more about cause.
Yes, run it as printed and schedule a visit if F2E4 stays.
Not by itself; the page stops at the line it prints.
The model and serial numbers, the exact display for F2E4, and what the top-load washer was doing at the time.
Maytag codes, symptoms, parts and service
For a top-load washer showing F2E3, Maytag prints “The F2 E3 alert indicates there may be an issue with the appliance control unit, user interface or associated...” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.