What it means
On a top-load washer, the entry for F2E5 says “The F2 E5 alert indicates there is an issue with the user interface or associated wiring.” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
Maytag washer F2E5 / User interface
On a top-load washer, the entry for F2E5 says “The F2 E5 alert indicates there is an issue with the user interface or associated wiring.” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
Also printed as F2E5
On a top-load washer, the entry for F2E5 says “The F2 E5 alert indicates there is an issue with the user interface or associated wiring.” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
Power and water off before any panel comes off; towels down for spills.
F2E5 returns, or the top-load washer behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Record F2E5 character by character and note the product type: top-load washer.

Power off for five full minutes, then on, and look for F2E5.

Give the washer a minute on screen after the reset; a returning F2E5 means schedule a visit.

Wipe the panel of the top-load washer with a dry or barely damp cloth; spills and grease upset keys.
Keep the model number close and note when F2E5 appeared and what the top-load washer was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The top-load washer entry for F2E5 reads “The F2 E5 alert indicates there is an issue with the user interface or associated wiring.” That is the whole explanation Maytag prints.
Read the supporting manualLeave the washer off power for five full minutes, switch it back on, and check the display for F2E5.
Read the supporting manualF2E4 is a separate entry from F2E5 on the top-load washer page, with its own wording.
Read the supporting manualA keypad problem is about control. If keys seem to press themselves, switch the top-load washer off at the breaker. If F2E5 keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13436 / PH 13436 (top-load washer)
F2E5 comes from Maytag Product Help (PH 13436) for the top-load washer, read in November 2026; the F2E5 entry names no models.
The help page states “The F2 E5 alert indicates there is an issue with the user interface or associated wiring.” Nothing else is added.
Yes, run it as printed and schedule a visit if F2E5 stays.
Not by itself; the page stops at the line it prints.
The model and serial numbers, the exact display for F2E5, and what the top-load washer was doing at the time.
Maytag codes, symptoms, parts and service
F2E4 on a Maytag top-load washer is explained as “The F2 E4 alert indicates there is an issue with the user interface or associated wiring.” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.