What it means
Maytag's wall oven page links F4E7 to the microwave meat probe, the meat probe receptacle or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Maytag oven F4E7 / Sensors
Maytag's wall oven page links F4E7 to the microwave meat probe, the meat probe receptacle or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Also printed as F4E7
Maytag's wall oven page links F4E7 to the microwave meat probe, the meat probe receptacle or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Turn the breaker off before you touch anything behind a panel.
F4E7 will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Turn the breaker off before you touch anything behind a panel. If you smell gas, leave the house and call your gas utility from outside.

Record F4E7 character by character and note the product type: wall oven.

Leave the breaker off a whole minute before checking for F4E7 again.

Once power is back, keep an eye on the oven for about a minute for F4E7.

Wipe the probe plug and socket dry once the wall oven is cool.
Keep the model number close and note when F4E7 appeared and what the wall oven was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
A wall oven showing F4E7 is, per Maytag, dealing with a possible problem in the microwave meat probe, the meat probe receptacle or the wiring. The page adds no diagnosis.
Read the supporting manualTurn the oven's circuit breaker off for one minute, switch it back on, then keep an eye on the oven for a further minute to see whether F4E7 comes back.
Read the supporting manualF4E6 sits beside F4E7 on the wall oven page and names the microwave wave guide temperature sensor or the wiring; the code names the microwave meat probe, the meat probe receptacle or the wiring.
Read the supporting manualOnly probe cooking is affected, so use time and temperature instead. If F4E7 keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14445 / PH 14445 (wall oven)
Facts for F4E7 are from the wall oven table (PH 14445) of Maytag Product Help, checked November 2026; no model list is printed.
The wall oven page ties F4E7 to the microwave meat probe, the meat probe receptacle or the wiring without saying which has failed.
Try it first: one minute off, one minute on screen. If F4E7 persists, a technician should look.
Maytag names the microwave meat probe, the meat probe receptacle or the wiring. Which one failed is for a technician with a meter to decide.
Tell us the model, the display wording and when F4E7 first showed up.
Maytag codes, symptoms, parts and service
F4 E6 names the microwave wave guide temperature sensor or its wiring, on the wall oven tree only. Switch the breaker off for one minute and back on, and tell us when the code appeared; book a visit if it returns.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.