What it means
F4 E5 names the microwave weight sensor or its wiring, and appears only on Maytag's wall oven pages. Switch the breaker off for one minute and back on, then tell us what the microwave was doing; book a visit if it returns.
Maytag oven F4E5 / Sensors
F4 E5 names the microwave weight sensor or its wiring, and appears only on Maytag's wall oven pages. Switch the breaker off for one minute and back on, then tell us what the microwave was doing; book a visit if it returns.
Also printed as F4E5
F4 E5 names the microwave weight sensor or its wiring, and appears only on Maytag's wall oven pages. Switch the breaker off for one minute and back on, then tell us what the microwave was doing; book a visit if it returns.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
F4 E5 returns after the breaker reset.
Your Maytag to-do list, saved here on this device

Say whether F4 E5 appeared at start-up or during a microwave program; it helps us plan the test.

Switch it off for one minute, then on, and watch the oven for one minute.

F4 E4 pairs the humidity sensor with the appliance manager, while this entry lists no manager.

The weight sensor is part of the microwave section and is tested on site.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
There may be a problem with the Microwave Weight Sensor, or the associated wiring. Maytag does not say what the sensor measures or give a cause beyond those two items.
Read the supporting manualF4 E3 names the exhaust air temperature sensor, F4 E4 the humidity sensor, F4 E5 the weight sensor and F4 E6 the wave guide temperature sensor.
Read the supporting manualNo. F4 E2 and F4 E4 list the microwave appliance manager next to a sensor, but F4 E5 lists only the weight sensor and the wiring.
Read the supporting manualReset the power at the breaker for one minute and watch the oven. If F4 E5 returns, book a visit; the page gives no owner repair.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14443 / PH 14443 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14441 / PH 14441 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14442 / PH 14442 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14444 / PH 14444 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14440 / PH 14440 (wall oven)
Wall oven page PH 14443, with PH 14440 to PH 14444 for the neighboring F4 E entries. The pages list no models.
Maytag publishes no range page for it. The code belongs to the microwave section of a combination wall oven.
Maytag's page does not describe the part or what it does. It names it only as a possible problem.
Yes, the page lists the associated wiring alongside the sensor. A technician tests both on site to find out which one it is.
Maytag gives no statement on that. If the code stays away after the reset you can test the oven; if it returns, stop and book a visit.
Maytag codes, symptoms, parts and service
The Maytag wall oven entry for F4E4 names the microwave humidity sensor, the microwave appliance manager or the wiring. Reset first, then call us in if the code keeps coming back.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.