What it means
F4 E6 names the microwave wave guide temperature sensor or its wiring, on the wall oven tree only. Switch the breaker off for one minute and back on, and tell us when the code appeared; book a visit if it returns.
Maytag oven F4E6 / Sensors
F4 E6 names the microwave wave guide temperature sensor or its wiring, on the wall oven tree only. Switch the breaker off for one minute and back on, and tell us when the code appeared; book a visit if it returns.
Also printed as F4E6
F4 E6 names the microwave wave guide temperature sensor or its wiring, on the wall oven tree only. Switch the breaker off for one minute and back on, and tell us when the code appeared; book a visit if it returns.
Turn the breaker off before you touch anything behind a panel.
F4 E6 returns after the breaker reset.
Your Maytag to-do list, saved here on this device

F4 E7 is the microwave meat probe code. Maytag says not to use the oven meat probe in the microwave.

Switch it off for one minute, then on, and watch the oven for one minute.

Say whether F4 E6 came at start-up or part way through a microwave program.

F4 E3 is the microwave exhaust air temperature sensor, another temperature entry.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
There may be a problem with the Microwave Wave Guide Temperature Sensor, or the associated wiring. Maytag does not describe the wave guide or say which of the two items is the cause.
Read the supporting manualF4 E3 names the microwave exhaust air temperature sensor and F4 E6 the wave guide temperature sensor. F4 E1 and F4 E2 name a thermistor.
Read the supporting manualF4 E5 is the weight sensor and F4 E7 the microwave meat probe, for which Maytag adds that the oven probe has a different resistance value.
Read the supporting manualReset the power at the breaker for one minute and watch the oven. If F4 E6 returns, book a visit; Maytag gives no owner repair for this sensor.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14444 / PH 14444 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14441 / PH 14441 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14439 / PH 14439 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14440 / PH 14440 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14443 / PH 14443 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14445 / PH 14445 (wall oven)
Wall oven page PH 14444, with PH 14439 to PH 14443 and PH 14445 for the neighboring F4 E entries. The pages list no models.
No. The microwave meat probe entry is F4 E7, which has its own page and tells you to seat the microwave probe in its receptacle.
No. Maytag publishes this code only for wall ovens, so a range owner should read the page for the code that actually shows.
Maytag's page does not describe it. It names the wave guide temperature sensor as one possible problem, together with the wiring.
Maytag gives no statement on that. If the code returns after the reset, stop using the microwave section and book a visit.
Maytag codes, symptoms, parts and service
F4 E5 names the microwave weight sensor or its wiring, and appears only on Maytag's wall oven pages. Switch the breaker off for one minute and back on, then tell us what the microwave was doing; book a visit if it returns.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.