Maytag oven F4E0 / Control board

Maytag oven
error code F4E0

Oven / display reference

F4 E0 is a wall oven code for combination models. Maytag names the microwave inverter or the wiring, and publishes no range page for it. Switch the breaker off for one minute and back on, then book a visit if it returns.

Also printed as F4E0

Last reviewed

Oven / display reference
Meaning
F4 E0 is a wall oven code for combination models. Maytag names the microwave inverter or the wiring, and publishes no range page for it. Switch the breaker off for one minute and back on, then book a visit if it returns.
Who handles it
Reset, then book
Related codes
Source
F4 E0 - Wall Oven - Product Help | Maytag

What Maytag oven F4E0 means.

What it means

F4 E0 is a wall oven code for combination models. Maytag names the microwave inverter or the wiring, and publishes no range page for it. Switch the breaker off for one minute and back on, then book a visit if it returns.

What you can safely check

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

When to call a technician

F4 E0 returns after the breaker reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 4 checks done
  1. Maytag oven F4E0: Wall oven with its top trim removed showing the green control board and fanned wire connectors, the black power cord and plug lying unplugged on the floor
    Illustration. Follow your model’s instructions.
    Before you begin

    Confirm you have a combination oven

    F4 E entries belong to the microwave section of a wall oven.

  2. Ranges & ovens in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Reset the breaker

    Switch it off for one minute, then on, and watch the oven for one minute.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Note the other F4 codes

    F4 E8 and F4 E9 name the same part; tell us if either appeared.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Leave the cabinet closed

    The inverter is inside the microwave section, so leave it to a technician.

Does F4E0 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

The touch panel and control.

Conceptual Range / oven sectionKeypad / touch panelControl boardElement wiring123
  1. 1Keypad / touch panel

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does F4 E0 mean?

Maytag says there may be a problem with the microwave inverter, or the associated wiring. The page does not describe the inverter or say which of the two is the cause.

Read the supporting manual

Which other codes name the inverter?

F4 E8 and F4 E9 both say "Microwave Inverter" in the same sentence. Maytag keeps a separate page for each of the three codes.

Read the supporting manual

What do the other F4 codes name?

F4 E1 names a thermistor or the appliance manager, F4 E2 the microwave sensor or thermistor and the manager, and F4 E3 the microwave exhaust air temperature sensor.

Read the supporting manual

What should I do when F4 E0 shows?

Reset the power at the breaker for one minute and watch the oven. If F4 E0 returns, book a visit; Maytag names the part but gives no owner repair.

Read the supporting manual

The manual behind the message.

Manufacturer document

F4 E0 - Wall Oven - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-11-08; PH 14438 / PH 14438 (wall oven)

Manufacturer document

F4 E8 - Wall Oven - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-11-08; PH 14446 / PH 14446 (wall oven)

Manufacturer document

F4 E9 - Wall Oven - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-11-08; PH 14447 / PH 14447 (wall oven)

Manufacturer document

F4 E1 - Wall Oven - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-11-08; PH 14439 / PH 14439 (wall oven)

Manufacturer document

F4 E2 - Wall Oven - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-11-08; PH 14440 / PH 14440 (wall oven)

Manufacturer document

F4 E3 - Wall Oven - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-11-08; PH 14441 / PH 14441 (wall oven)

Wall oven page PH 14438 with PH 14439 to PH 14441, 14446 and 14447; Maytag has no range page for F4 E0. The pages list no models.

Here to help

Good questions.
Clear answers.

Talk to our team
Does F4 E0 affect the main oven?

Maytag does not say. The page is about the microwave inverter, so tell us whether the main oven still bakes when you book.

Why are there three inverter codes?

Maytag does not explain. F4 E0, F4 E8 and F4 E9 print the same cause, and we list each on its own page because Maytag does.

Is there an F4 E0 page for ranges?

No. Maytag publishes the F4 E codes only for wall ovens, so a freestanding range should use the page for the code it actually shows.

What does the breaker reset do?

It removes power from the control for a minute so it can restart. Maytag then asks you to watch the oven for another minute to see if the code returns.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.