What it means
F3-1 on a range means Maytag suspects the oven temperature sensor, the control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
Maytag oven F3-1 / Sensors
F3-1 on a range means Maytag suspects the oven temperature sensor, the control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
Also printed as F3-1
F3-1 on a range means Maytag suspects the oven temperature sensor, the control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
F3-1 repeats after the reset.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

Record F3-1 character by character and note the product type: range.

Leave the breaker off a whole minute before checking for F3-1 again.

Give the oven a minute on screen after the reset; a returning F3-1 means schedule a visit.

Do not bend or poke the sensor inside the range; panel work belongs to a technician.
Keep the model number close and note when F3-1 appeared and what the range was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue.
Read the definitionA range showing F3-1 is, per Maytag, dealing with a possible problem in the oven temperature sensor, the control or the wiring. The page adds no diagnosis.
Read the supporting manualTake the oven off power at the breaker for a full minute. Put it back on and give it a minute of watching; if F3-1 stays away, the reset did its job.
Read the supporting manualF3E0 carries the same parts list as F3-1 on the range page. The reset is the same, only the code differs.
Read the supporting manualDo not rely on the dial alone while this is open; a food thermometer is the safer guide.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13772 / PH 13772 (range)
F3-1 comes from Maytag Product Help (PH 13772) for the range, read in November 2026; the F3-1 entry names no models.
Maytag lists the oven temperature sensor, the control or the wiring. It is a possible-cause list, not a confirmed failure.
Try it first: one minute off, one minute on screen. If F3-1 persists, a technician should look.
Maytag names the oven temperature sensor, the control or the wiring. Which one failed is for a technician with a meter to decide.
The model number, what F3-1 looked like, and whether the reset changed anything.
Maytag codes, symptoms, parts and service
Maytag's pages split on F3: the pages for the range and wall oven state the page names these possible trouble spots: oven control together with its wiring; the steam oven page offers a reset and nothing more. To reset it, leave the circuit breaker off for 1 minute before switching it back on.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.