What it means
4D22 means the cooling fan speed is too low. Maytag names three suspects: an airflow restriction, the oven cooling fan, or the wiring. Check that nothing blocks the vents, then reset the power for one minute.
Maytag oven 4d22 / Fan and airflow
4D22 means the cooling fan speed is too low. Maytag names three suspects: an airflow restriction, the oven cooling fan, or the wiring. Check that nothing blocks the vents, then reset the power for one minute.
Also printed as 4d22
4D22 means the cooling fan speed is too low. Maytag names three suspects: an airflow restriction, the oven cooling fan, or the wiring. Check that nothing blocks the vents, then reset the power for one minute.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
4D22 returns after the vents are clear and the reset is done.
Your Maytag to-do list, saved here on this device

Check for anything that could block air around the oven. Maytag lists an airflow restriction first.

During preheat, mid-bake or after a cycle: that detail helps us at the visit.

Off for one minute, then on. Monitor the oven for one minute.

Start a bake and listen for the cooling fan to come on.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
A Maytag range carries a cooling fan whose job is to protect the oven cavity and electronics from heat during BAKE, BROIL and CLEAN.
Read the definitionCooling fan speed too low. There may be a problem with an airflow restriction, the oven cooling fan, or the associated wiring.
Read the supporting manual4D22 is "too low" and 4D42 is "too high." Both pages list the same three suspects, including an airflow restriction.
Read the supporting manualA separate message page covers "too low or too high" together and lists the same airflow restriction, fan and wiring.
Read the supporting manualMaytag gives no statement on continued use. If the code returns after the reset, stop using the oven and book a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13718 / PH 13718 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14378 / PH 14378 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-07; PH 13889 / PH 13889 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13722 / PH 13722 (range)
Product Help range page PH 13718 and wall oven page PH 14378, with the Cooling Fan Speed message PH 13889 and the 4D21 page PH 13717. No models are listed.
Maytag prints a separate page for 4D21 with the same "too low" wording.
Maytag does not define it on the page; it appears in the list of possible problems.
The page lists the associated wiring as a possibility, along with the fan and an airflow restriction.
Yes, with the same text.
Maytag codes, symptoms, parts and service
For 4d21, the Maytag range page points to the airflow restriction, the oven cooling fan or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
A Maytag range carries a cooling fan whose job is to protect the oven cavity and electronics from heat during BAKE, BROIL and CLEAN. Product Help says it can keep spinning for a long while after the oven goes off. A Cooling Fan Speed message means its speed is off.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.