What it means
Maytag Product Help prints FAE4 or F10E4 as “Potential Cause: Diverter Valve Error,” with one step: cycle power. Its leak-check steps belong to the next code, FAE5. If FAE4 returns, book a technician.
Maytag dishwasher FAE4 / Water and drain
Maytag Product Help prints FAE4 or F10E4 as “Potential Cause: Diverter Valve Error,” with one step: cycle power. Its leak-check steps belong to the next code, FAE5. If FAE4 returns, book a technician.
Also printed as FAE4
Maytag Product Help prints FAE4 or F10E4 as “Potential Cause: Diverter Valve Error,” with one step: cycle power. Its leak-check steps belong to the next code, FAE5. If FAE4 returns, book a technician.
Close the water valve and the breaker before any panel comes off.
FAE4 returns after the power cycle.
Your Maytag to-do list, saved here on this device

Unplug the dishwasher for 30 seconds, or turn its breaker off for 30 seconds if it is hard wired, then restore power.

The page is titled FAE4 or F10E4. On a flashing-light model F10E4 is ten rapid flashes, a pause, then four flashes.

Checking under the dishwasher and pressing Cancel twice belong to FAE5, not to FAE4. [2]

After the reset, start one cycle to see whether the code returns.

Dry floors show nothing leaked. If it is wet, report it when you book.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag dishwasher, FAE4 lists a diverter valve error and FAE5 lists a diverter leak.
Read the definitionIt names a diverter valve error and gives one remedy, cycle power. Unlike the other dishwasher pages, it prints no line about scheduling service.
Read the supporting manualFAE5 or F10E5 is a diverter leak with four steps: check for leaks under the dishwasher, make sure all water connections are secure, press Cancel twice, and try a new cycle; if the error returns, schedule service.
Read the supporting manualThe page title lists both. The Reading page explains that the flashing pattern gives the F number, then the E number, which is how a ten-flash group becomes F10.
Read the supporting manualThe retailer-copy manual prints no diverter code. It says call for service when the Clean light or other lights blink and the dishwasher will not run.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 15080 / PH 15080 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12637 / PH 12637 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-08-31; PH 15083 / PH 15083 (dishwasher)
Manufacturer document
Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)
W10401489A (1/12); printed page numbers; retailer copy / printed p11, “Blinking lights” row
Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Source: Product Help PH 15080, with the FAE5 and Reading pages.
Maytag does not define it on the page; our diverter term page covers the part.
No. FAE5 is the leak code.
Yes, the page lists them as alternatives.
The page ends after the power cycle. If the code stays, treat it as a visit.
Maytag codes, symptoms, parts and service
Maytag's dishwasher page words F9E2 like this: “Potential Cause: Drain motor error.” No reset is printed for it, so schedule a visit if it keeps appearing.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
On a Maytag dishwasher, FAE4 lists a diverter valve error and FAE5 lists a diverter leak. For FAE5, Product Help says to check for leaks under the dishwasher, make sure water connections are secure, press Cancel twice and start a new cycle. FAE4 gets a 30-second power reset.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.