What it means
Maytag Product Help prints F8E2 as “Potential Cause: Fill Valve Electric Error.” Remove the drip tray and inspect the inlet valve connection for leaks, then cycle power. If F8E2 returns, schedule service.
Maytag dishwasher F8E2 / Water and drain
Maytag Product Help prints F8E2 as “Potential Cause: Fill Valve Electric Error.” Remove the drip tray and inspect the inlet valve connection for leaks, then cycle power. If F8E2 returns, schedule service.
Also printed as F8E2
Maytag Product Help prints F8E2 as “Potential Cause: Fill Valve Electric Error.” Remove the drip tray and inspect the inlet valve connection for leaks, then cycle power. If F8E2 returns, schedule service.
Close the water valve and the breaker before any panel comes off.
F8E2 returns after the drip tray check and power cycle.
Your Maytag to-do list, saved here on this device

The page says to remove the drip tray and inspect the inlet valve connection, ensuring no leaks. Water in the tray is a reason to stop and call.

Unplug the dishwasher for 30 seconds, or turn its breaker off for 30 seconds if it is hard wired, then restore power.

Removing the drip tray can spill water onto the floor; place a towel before you pull it.

The F8E4 page warns that the float switch wire is connected to the tray and that pulling too far or too hard can damage it. [3]

After the reset, start a cycle and see whether F8E2 returns while the dishwasher fills.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F8E5 on a Maytag dishwasher lists a fill valve stuck open, and the page leads with stopping the water.
Read the definitionThe cause is a fill valve electric error. The troubleshooting steps are to remove the drip tray and inspect the inlet valve connection, ensuring no leaks, and then to power cycle; if the error returns, schedule service.
Read the supporting manualF8E5 is a fill valve stuck open, and its steps are different: turn off the water if possible, press Cancel once, keep the door closed and do not turn off the power; if you cannot shut the water off, turn off power. F8E2 has no such emergency steps.
Read the supporting manualF8E4 is water detected in the drip tray, with checks on connections, the float switch and emptying the tray. F8E2 only asks you to look at the inlet valve connection.
Read the supporting manualThe retailer-copy troubleshooting table for “will not fill” says to be sure the water is on, check the float is free, and look for suds.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12631 / PH 12631 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12633 / PH 12633 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12632 / PH 12632 (dishwasher)
Manufacturer document
Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)
W10401489A (1/12); printed page numbers; retailer copy / printed p11, “Blinking lights” row
Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Source: Product Help PH 12631, with the F8E5 and F8E4 pages.
Not by the cause line, but the page asks you to check for leaks at the inlet valve.
No shutoff is printed for F8E2; that instruction belongs to F8E5.
The F8E4 page describes pressing the snap at each side of the plastic tray toward the center and pulling it toward you.
Stop, turn off the water, and book a visit.
Maytag codes, symptoms, parts and service
Maytag Product Help prints F7E2 as “Potential Cause: Wash Motor Error,” and its Reading error codes page lists the same row. Cycle power; if the error code returns, schedule service.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
F8E5 on a Maytag dishwasher lists a fill valve stuck open, and the page leads with stopping the water. Product Help says to shut the water supply when you can reach it, press Cancel one time to quiet the tone, and close the door. Leave power on unless the water cannot be stopped.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.