What it means
Maytag Product Help prints F7E2 as “Potential Cause: Wash Motor Error,” and its Reading error codes page lists the same row. Cycle power; if the error code returns, schedule service.
Maytag dishwasher F7E2 / Motor and drive
Maytag Product Help prints F7E2 as “Potential Cause: Wash Motor Error,” and its Reading error codes page lists the same row. Cycle power; if the error code returns, schedule service.
Also printed as F7E2
Maytag Product Help prints F7E2 as “Potential Cause: Wash Motor Error,” and its Reading error codes page lists the same row. Cycle power; if the error code returns, schedule service.
Switch off power and the water supply before opening anything, and wipe up spills so nobody slips.
F7E2 returns after the power cycle.
Your Maytag to-do list, saved here on this device

Unplug the dishwasher for 30 seconds, or turn its breaker off for 30 seconds if it is hard wired, then restore power.

After the reset, start a cycle and listen for the wash action. A dishwasher that fills but makes no spray noise should be reported.

Look for a utensil or dish touching the spray arm. This is our own check; Maytag prints none for F7E2.

Humming, grinding or silence before F7E2 helps a technician.
The retailer-copy manual says to call for service if the Clean light or other lights blink and the dishwasher will not run. [4]
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Wash motor error, with the instruction “Power Cycle, If the error code returns, schedule service.”
Read the supporting manualIts common-codes table repeats “F7E2 Wash Motor Error” with the same instruction. It adds nothing new for F7E2.
Read the supporting manualF9E2 is a drain motor error and lists drain checks: knockout plug, disposer and drain clogs, a kinked hose and its routing. F7E2 lists no such checks because the wash motor is not a drain part.
Read the supporting manualMaytag prints no warning. Stop after one reset and one restart if F7E2 returns.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12630 / PH 12630 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-08-31; PH 15083 / PH 15083 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12636 / PH 12636 (dishwasher)
Manufacturer document
Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)
W10401489A (1/12); printed page numbers; retailer copy / printed p11, “Blinking lights” row
Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Source: Product Help PH 12630, with the Reading error codes page and the F9E2 page.
Maytag does not describe it further.
No. Drain codes are F9E1 and F9E2.
No home repair is printed.
The model, the exact code and whether the dishwasher still fills.
Maytag codes, symptoms, parts and service
Maytag Product Help prints F6E4 as “Potential Cause: Water Float Switch,” and its first question is whether the dishwasher is level. An unlevel dishwasher can trip the overfill or floater switch. Level it, then cycle power.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.