What it means
F40 on your electric cooktop is tied by Maytag to the user interface (touchpad), the cooktop power control board or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Maytag cooktop F40 / User interface
F40 on your electric cooktop is tied by Maytag to the user interface (touchpad), the cooktop power control board or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Also printed as F40
F40 on your electric cooktop is tied by Maytag to the user interface (touchpad), the cooktop power control board or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Turn the breaker off before you touch anything behind a panel, and leave wiring and supply connections to a technician.
F40 repeats after the reset.
Your Maytag to-do list, saved here on this device

Turn the breaker off before you touch anything behind a panel, and leave wiring and supply connections to a technician.

Match the label on your appliance to the electric cooktop list before you rely on the wording for F40.

Cut power at the breaker for a minute, restore it, then check for F40.
Once power is back, keep an eye on the cooktop for about a minute for F40.
Check whether the electric cooktop still lights and answers touch while F40 shows.
Write down the model and serial numbers and the exact F40 wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
The touch control is the keypad on a Maytag electric cooktop.
Read the definition
Component reference
The power control board, called the power control module on some pages, is the cooktop part that Maytag Product Help names for F40, F42, F43, F47, F58 and F64.
Read the definitionA electric cooktop showing F40 is, per Maytag, dealing with a possible problem in the user interface (touchpad), the cooktop power control board or the wiring. The page adds no diagnosis.
Read the supporting manualTake the cooktop off power at the breaker for a full minute. Put it back on and give it a minute of watching; if F40 stays away, the reset did its job.
Read the supporting manualF36 sits beside F40 on the electric cooktop page and names the temperature sensor on an induction coil; the code names the user interface (touchpad), the cooktop power control board or the wiring.
Read the supporting manualKeep the electric cooktop off until F40 is explained if touch controls act oddly. If the code keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-01-22; PH 12870 / PH 12870 (electric cooktop)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2022-03-24; PH 11988 / PH 11988 (electric cooktop)
Scope for F40: Maytag electric cooktop, PH 12870, checked November 2026. Maytag lists no models on the F40 page.
Maytag lists the user interface (touchpad), the cooktop power control board or the wiring. It is a possible-cause list, not a confirmed failure.
Try it first: one minute off, one minute on screen. If F40 persists, a technician should look.
Maytag names the user interface (touchpad), the cooktop power control board or the wiring. Which one failed is for a technician with a meter to decide.
Tell us the model, the display wording and when F40 first showed up.
Maytag codes, symptoms, parts and service
Maytag’s F36 pages do not agree. Two say a temperature sensor on an induction coil; the radiant element page says communication between the touch control module and the electronic control. Reset at the breaker for one minute.
A Maytag electric cooktop that keeps beeping may have something on the control area, Control Lock being turned on or off, or a utensil left on an element too long. Clear and wipe the control panel first. Beeping for more than 15 minutes locks the panel and can show F1E0 on some models.
The touch control is the keypad on a Maytag electric cooktop. It is the part you touch to turn cooking areas on and set heat. Product Help calls it the user interface, touchpad or touch control module, and its F22, FC E1 and F6E0 pages point to it. The first step printed is a one-minute breaker reset.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.