Inside the appliance
Microwave power failure display (0:00, PF). In plain English.
On a Maytag microwave, a flashing 0:00 on a countertop model, or a blinking colon or PF on an over-the-range one, means power was lost or the clock is off. Product Help says to touch Cancel, then reset the clock. If it keeps flashing, it says to call a qualified electrician.

Where it fits.
Microwave power failure display (0:00, PF) in the appliance
On the display of any Maytag microwave, in the clock area.
This image is an example of the component type. It will not tell you which replacement is right for your model.
How you can tell this system is asking for attention.
Microwave power failure display (0:00, PF) trouble can show up along with weaker performance or a code that keeps coming back. It takes testing to say whether this component is the reason.

Maytag microwave will not start
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.

Maytag countertop microwave control panel bubbling
Bubbles on the control panel of a Maytag countertop microwave are usually the clear protective film that ships over the panel. Lift one corner with a fingernail and peel it off; there may be more than one layer. If the panel still looks raised, book a technician.
Owner care, within the model instructions.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Read the display
Flashing 0:00, a blinking colon or PF all point to lost power or the clock being off.
- 2
Touch Cancel
Cancel or Cancel/Off stops the blinking, depending on the model.
- 3
Reset the clock
Enter the time again. A bad entry beeps and asks again.
- 4
Watch it hold
If it keeps flashing, the supply needs a look.
Cleaning or replacement?
Leave internal testing to a technician.
PF or the colon keeps flashing after the clock is set.
The microwave loses its time often with no outage.
Other appliances on that circuit have lost power too.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Microwave power failure display (0:00, PF) advice. Read the manual for your own model.
- Flashing 0:00 - Error Code - Countertop Microwave - Product Help | Maytag
- Flashing ":" or PF in display - Over-the-Range Microwave - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
Why is my microwave flashing 0:00?
Product Help says it means there has been a power failure.
What does PF mean?
On over-the-range models, a power failure or the clock time turned off.
How do I stop the blinking?
Touch Cancel or Cancel/Off, then set the clock.
When is it more than the clock?
Product Help says to call a qualified electrician if the colon or PF keeps flashing.
Maytag codes, symptoms, parts and service
From the message to what you do next.
Flashing 0:00
On a countertop microwave, the entry for Flashing 0:00 says “A flashing '0:00' means there has been a power failure.” No reset is printed for it, so schedule a visit if it keeps appearing.
Maytag microwave will not start
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
Microwave repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.

