Maytag washer FCE0 / Reset only

Maytag washer
error code FCE0

Washer / display referenceFCE0

Maytag’s front-load washer page for FCE0 (PH 14630) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if FCE0 returns.

Also printed as FCE0

Last reviewed

Washer / display referenceFCE0
Meaning
Maytag’s front-load washer page for FCE0 (PH 14630) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if FCE0 returns.
Who handles it
Reset, then book
Source
FC E0 - Front Load Washer - Product Help | Maytag

What Maytag washer FCE0 means.

What it means

Maytag’s front-load washer page for FCE0 (PH 14630) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if FCE0 returns.

What you can safely check

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

When to call a technician

FCE0 returns, or the front-load washer behaves oddly around the code.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 6 checks done
  1. Maytag washer FCE0: Hand pressing a round button on a top-load washer panel next to a dial and a lit display, with a detergent jug on the shelf above
    Illustration. Follow your model’s instructions.
    Before you begin

    Safety first

    Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Match your model

    Check that your appliance is a front-load washer and copy FCE0 exactly as the display shows it.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Power-cycle it

    Wait five minutes without power before you check for FCE0 again.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Retest briefly

    Give the washer a minute on screen after the reset; a returning FCE0 means schedule a visit.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Appliance-specific check

    The control board lives behind panels on the front-load washer; keep them closed.

  6. Illustration. Follow your model’s instructions.
    Check 6

    Gather details

    Keep the model number close and note when FCE0 appeared and what the front-load washer was doing.

Does FCE0 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

The control and its sensors.

Conceptual Washer sectionControl panelControl boardLevel sensorMotor wiring1234
  1. 1Control panel
  2. 2Control board
  3. 4Motor wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does Maytag say FCE0 means?

Nothing. The front-load washer page (PH 14630, modified November 2025) gives no cause, no part and no meaning for FCE0; it has only a power reset.

Read the supporting manual

How do I reset the washer for FCE0?

Unplug the washer for 5 minutes and plug it back in, or switch its breaker off for 5 minutes and back on. Maytag compares it to restarting a computer.

Read the supporting manual

Will the reset fix FCE0?

Maytag says resetting the control can sometimes solve the issues you are experiencing, but it does not promise it. After the 5 minutes, watch the display for FCE0; if it is gone, run a short cycle and keep an eye on the washer.

Read the supporting manual

What should I tell the technician about FCE0?

Give us the model and serial numbers, the exact display, and what the washer was doing when FCE0 appeared. Say whether the reset cleared it, even for a short time, because a code that returns is the reason to book a visit.

Read the supporting manual

The manual behind the message.

Manufacturer document

FC E0 - Front Load Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-11-19; PH 14630 / PH 14630 (front-load washer)

Facts for FCE0 come from Maytag Product Help, front-load washer page (PH 14630), read in November 2026. The pages list no models.

Here to help

Good questions.
Clear answers.

Talk to our team
Does Maytag say what FCE0 means on a washer?

No. The front-load washer page prints only the reset instruction and no cause, so we cannot name a failed part and will not guess one.

How long should the washer stay without power for FCE0?

Five minutes, as printed. Unplug the washer or switch off its breaker for the full 5 minutes before restoring power, because a shorter wait may not reset the control.

Is there a top-load washer page for FCE0?

Not in the sources we hold. We cite only the front-load washer page (PH 14630), so we describe FCE0 for front-load washers only.

When should I book a visit for FCE0?

Book a visit if FCE0 returns after the 5-minute reset, or if the washer behaves oddly in other ways. Have the model and serial numbers ready.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.