What it means
On a range, the entry for Feature Not Available or Fault Detected says a line saying the control has detected a problem Switch the breaker off for a minute, then back on; schedule a visit if the code is still there.
Maytag oven Feature Not Available or Fault Detected / Control board
On a range, the entry for Feature Not Available or Fault Detected says a line saying the control has detected a problem Switch the breaker off for a minute, then back on; schedule a visit if the code is still there.
Also printed as Feature Not Available or Fault Detected
On a range, the entry for Feature Not Available or Fault Detected says a line saying the control has detected a problem Switch the breaker off for a minute, then back on; schedule a visit if the code is still there.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
Feature Not Available or Fault Detected repeats after the reset.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

Record Feature Not Available or Fault Detected character by character and note the product type: range.

Leave the breaker off a whole minute before checking for Feature Not Available or Fault Detected again.

Give the oven a minute on screen after the reset; a returning Feature Not Available or Fault Detected means schedule a visit.

Note when Feature Not Available or Fault Detected appears: at start, mid-cycle or after a power cut.
Keep the model number close and note when Feature Not Available or Fault Detected appeared and what the range was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Feature Not Available or Fault Detected is covered by this wording on the range page: a line saying the control has detected a problem
Read the supporting manualTake the oven off power at the breaker for a full minute. Put it back on and give it a minute of watching; if Feature Not Available or Fault Detected stays away, the reset did its job.
Read the supporting manualDemo Mode is a separate entry from Feature Not Available or Fault Detected on the range page, with its own wording.
Read the supporting manualWhen in doubt, switch the range off. Never open a panel on the range yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-07; PH 13881 / PH 13881 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14345 / PH 14345 (wall oven)
Feature Not Available or Fault Detected comes from Maytag Product Help (PH 13881) for the range, read in November 2026; the Feature Not Available or Fault Detected entry names no models.
The range page reads a line saying the control has detected a problem It prints nothing more about cause.
It sometimes does. Breaker off for a full minute, then on, then a minute of watching. If Feature Not Available or Fault Detected returns, schedule a visit.
Nothing about replacing parts is printed for Feature Not Available or Fault Detected.
The model and serial numbers, the exact display for Feature Not Available or Fault Detected, and what the range was doing at the time.
Maytag codes, symptoms, parts and service
Demo Mode keeps the oven from heating so a control can be shown on a sales floor. Maytag says that while it is on, the oven will not work. Turn it off on the settings screen. The steps differ between a range keypad and a touchscreen wall oven.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.