What it means
F1-E on a range means Maytag suspects the oven control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
Maytag oven F1-E / Control board
F1-E on a range means Maytag suspects the oven control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
Also printed as F1-E
F1-E on a range means Maytag suspects the oven control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
F1-E returns, or the range behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

Record F1-E character by character and note the product type: range.

Breaker off for one full minute, then back on, and look for F1-E.

Once power is back, keep an eye on the oven for about a minute for F1-E.

The control board lives behind panels on the range; keep them closed.
Keep the model number close and note when F1-E appeared and what the range was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
Maytag range pages for F1-7, F3 and F6 point at the control board of the oven, or the wiring to it.
Read the definitionFor F1-E the range entry names the oven control or the wiring. Nothing in it says which of them has failed.
Read the supporting manualTake the oven off power at the breaker for a full minute. Put it back on and give it a minute of watching; if F1-E stays away, the reset did its job.
Read the supporting manualF1-C sits beside F1-E on the range page and names the oven door latch, the door lock switch or the wiring; the code names the oven control or the wiring.
Read the supporting manualThe control runs everything on the range, so a returning F1-E is a reason to stop using it.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13754 / PH 13754 (range)
Scope for F1-E: Maytag range, PH 13754, checked November 2026. Maytag lists no models on the F1-E page.
Maytag lists the oven control or the wiring. It is a possible-cause list, not a confirmed failure.
It sometimes does. Breaker off for a full minute, then on, then a minute of watching. If F1-E returns, schedule a visit.
Maytag names the oven control or the wiring. Which one failed is for a technician with a meter to decide.
The model number, what F1-E looked like, and whether the reset changed anything.
Maytag codes, symptoms, parts and service
Maytag's range page links F1-C to the oven door latch, the door lock switch or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
Maytag range pages for F1-7, F3 and F6 point at the control board of the oven, or the wiring to it. F1-8 also names the keypad and its interface. The only home step printed is a one-minute breaker reset, followed by watching the oven.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.