What it means
The Maytag range entry for 9d42 names the oven door latch assembly, the door switch or the wiring. Reset first, then call us in if the code keeps coming back.
Maytag oven 9d42 / Door and lid
The Maytag range entry for 9d42 names the oven door latch assembly, the door switch or the wiring. Reset first, then call us in if the code keeps coming back.
Also printed as 9d42
The Maytag range entry for 9d42 names the oven door latch assembly, the door switch or the wiring. Reset first, then call us in if the code keeps coming back.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
9d42 returns, or the range behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

Match the label on your appliance to the range list before you rely on the wording for 9d42.

Leave the breaker off a whole minute before checking for 9d42 again.

Once power is back, keep an eye on the oven for about a minute for 9d42.

If 9d42 showed after a self-clean, wait until the range is cool before you touch the door or the latch.
Keep the model number close and note when 9d42 appeared and what the range was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F5 on a Maytag range or wall oven names the door latch assembly, the latch switches and the wiring as suspects.
Read the definition9d42 is printed against the oven door latch assembly, the door switch or the wiring. Maytag words it as a possible problem, not a finding.
Read the supporting manualMaytag's reset is a minute at the breaker: off, wait, on. Then leave the oven in view for another minute and note whether 9d42 returns.
Read the supporting manualMaytag gives 9d41 and 9d42 the same wording on the range page, so the same first step fits both.
Read the supporting manualThe page names the latch side, so the lock may not work as it should. Skip self-clean cycles until the range is checked.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13732 / PH 13732 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14392 / PH 14392 (wall oven)
Facts for 9d42 are from the range table (PH 13732) of Maytag Product Help, checked November 2026; no model list is printed.
Maytag names the oven door latch assembly, the door switch or the wiring and gives no test to choose between them.
It is the page's first step and costs nothing. A returning 9d42 afterward means schedule us.
The list is the oven door latch assembly, the door switch or the wiring; testing on site settles it.
Model and serial numbers plus a note of what happened when 9d42 appeared.
Maytag codes, symptoms, parts and service
Maytag's range page links 9d41 to the oven door latch assembly, the door switch or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
F5 on a Maytag range or wall oven names the door latch assembly, the latch switches and the wiring as suspects. Product Help gives a one-minute breaker reset and asks you to verify oven operation afterward. A steam oven F5 page lists the reset alone.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.