What it means
Maytag's range page links 9d31 to the oven door latch assembly, the door switch or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Maytag oven 9d31 / Door and lid
Maytag's range page links 9d31 to the oven door latch assembly, the door switch or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Also printed as 9d31
Maytag's range page links 9d31 to the oven door latch assembly, the door switch or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
9d31 returns, or the range behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

Check that your appliance is a range and copy 9d31 exactly as the display shows it.

Cut power at the breaker for a minute, restore it, then check for 9d31.

Run the oven briefly after the reset and see whether 9d31 comes back.

Look at the door seal on the range: it should close fully with nothing caught in it.
Note the model and the moment 9d31 showed up; both help us plan.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F5 on a Maytag range or wall oven names the door latch assembly, the latch switches and the wiring as suspects.
Read the definitionThe range list ties 9d31 to the oven door latch assembly, the door switch or the wiring. That is a set of candidates, and the page does not pick one.
Read the supporting manualMaytag's reset is a minute at the breaker: off, wait, on. Then leave the oven in view for another minute and note whether 9d31 returns.
Read the supporting manual9d22 carries the same parts list as 9d31 on the range page. The reset is the same, only the code differs.
Read the supporting manualA latch problem concerns the door and not the heat, so cook normally and keep cleaning cycles off.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13729 / PH 13729 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14389 / PH 14389 (wall oven)
9d31 comes from Maytag Product Help (PH 13729) for the range, read in November 2026; the 9d31 entry names no models.
9d31 is printed against the oven door latch assembly, the door switch or the wiring; the page does not narrow it down.
Try it first: one minute off, one minute on screen. If 9d31 persists, a technician should look.
No. the oven door latch assembly, the door switch or the wiring are all candidates and the page gives no way to choose.
The model and serial numbers, the exact display for 9d31, and what the range was doing at the time.
Maytag codes, symptoms, parts and service
For 9d22, the Maytag range page points to the oven door latch assembly, the door switch or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
F5 on a Maytag range or wall oven names the door latch assembly, the latch switches and the wiring as suspects. Product Help gives a one-minute breaker reset and asks you to verify oven operation afterward. A steam oven F5 page lists the reset alone.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.