Maytag dryer F3E1 / Reset only

Maytag dryer
error code F3E1

Dryer / display reference

Maytag’s two F3E1 pages disagree. The standard dryer page says “Exhaust Thermistor” and a one-minute breaker reset; the commercial-grade residential page names no cause and says five minutes without power. Check which dryer you own.

Also printed as F3E1

Last reviewed

Dryer / display reference
Meaning
Maytag’s two F3E1 pages disagree. The standard dryer page says “Exhaust Thermistor” and a one-minute breaker reset; the commercial-grade residential page names no cause and says five minutes without power. Check which dryer you own.
Who handles it
Reset, then book
Related codes
Source
F3 E1 - Error Code - Commercial Dryer - Product Help | Maytag

What Maytag dryer F3E1 means.

What it means

Maytag’s two F3E1 pages disagree. The standard dryer page says “Exhaust Thermistor” and a one-minute breaker reset; the commercial-grade residential page names no cause and says five minutes without power. Check which dryer you own.

What you can safely check

Unplug the dryer or switch off its breaker before opening any panel, clean lint regularly, and if you smell gas leave the house and call your gas utility.

When to call a technician

F3E1 returns after the reset and a timed dry cycle.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag dryer F3E1: Hand pressing the start button on a dryer control panel with a steel cycle knob beside a lit display reading 00
    Illustration. Follow your model’s instructions.
    Before you begin

    Find out which page fits your dryer

    A commercial-grade residential dryer follows the five-minute page. A standard residential dryer follows the exhaust thermistor page with the one-minute reset.

  2. Dryers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Breaker off, then wait

    One minute on the standard page, five minutes on the commercial-grade page.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Start a timed dry cycle

    Both pages tell you to start a time dry cycle after power returns.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Monitor the display

    One minute on both pages.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Check the lint screen and vent

    F3E1 names an exhaust thermistor, which reads exhaust air. A clogged lint screen or vent is our own first look; Maytag does not print it for this code.

Does F3E1 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Heat and its safety limits.

Conceptual Dryer sectionHeaterThermostat / fuseDrumControl1234
  1. 1Heater
  2. 2Thermostat / fuse
  3. 3Drum
  4. 4Control

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Parts behind the message.

Hand lifting a mesh lint screen full of gray lint out of its slot below the open dryer drum

Component reference

Dryer lint screen

The lint screen is the removable screen that catches lint from the air leaving a Maytag dryer.

Read the definition

A little more context.

What do the two F3E1 pages say?

The commercial-grade residential dryer page gives only the reset: breaker off for 5 minutes, back on, a timed dry cycle, and a one-minute watch. The standard dryer page adds the heading “Exhaust Thermistor” and uses a one-minute breaker reset.

Read the supporting manual

How is F3E1 different from F3E3?

F3E3 is headed “Inlet Thermistor” and uses the same one-minute reset. F3E1 concerns the exhaust side.

Read the supporting manual

How is F3E1 different from F3E5?

F3E5 is a moisture sensor code with leveling and small-load checks and a five-consecutive-loads explanation. F3E1 has none of that.

Read the supporting manual

Is the dryer safe to use?

Maytag does not say. If a hot or burning smell accompanies the code, stop and unplug the dryer or switch off its breaker.

Read the supporting manual

The manual behind the message.

Manufacturer document

F3 E1 - Error Code - Commercial Dryer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-10-21; PH 11822 / PH 11822 (commercial-grade residential dryer)

Manufacturer document

F3 E1 - Error Code - Dryer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2026-08-19; PH 12805 / PH 12805 (dryer)

Manufacturer document

F3 E3 - Error Code - Dryer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2026-08-19; PH 12807 / PH 12807 (dryer)

Manufacturer document

F3 E5 - Error Code - Dryer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 12809 / PH 12809 (dryer)

Maytag's Product Help names no model range for this code. The cited pages cover a commercial-grade residential dryer and a standard dryer. Sources: Product Help PH 11822 (commercial-grade residential dryer) and PH 12805 (dryer), with the F3E3 and F3E5 pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Is F3E1 a thermistor code?

On the standard dryer page, yes: it is headed Exhaust Thermistor. The commercial page does not say.

One minute or five?

The standard dryer page says one minute; the commercial-grade page says five.

Does lint cause F3E1?

Maytag does not say. Clean the lint screen anyway; it is routine.

Do I start a cycle after the reset?

Yes, a timed dry cycle, per both pages.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.