What it means
Maytag Product Help prints F4E3 as “Potential Cause: Heating Error.” Cycle power for 30 seconds; if the error code returns, schedule service. F4E2 reads “Heating System” and has the same remedy.
Maytag dishwasher F4E3 / Heating
Maytag Product Help prints F4E3 as “Potential Cause: Heating Error.” Cycle power for 30 seconds; if the error code returns, schedule service. F4E2 reads “Heating System” and has the same remedy.
Also printed as F4E3
Maytag Product Help prints F4E3 as “Potential Cause: Heating Error.” Cycle power for 30 seconds; if the error code returns, schedule service. F4E2 reads “Heating System” and has the same remedy.
Close the water valve and the breaker before any panel comes off.
F4E3 returns after the 30-second power cycle.
Your Maytag to-do list, saved here on this device

Unplug the dishwasher for 30 seconds, or turn its breaker off for 30 seconds if it is hard wired, then restore power.

A heating error can follow a hot cycle. Wait before you open the door.

After the reset, start a cycle and watch whether F4E3 returns.

Note whether it showed at the start, in the wash or in the dry phase. The page gives no timing, so your note helps.
The retailer-copy manual says call for service if the Clean light or any other light blinks and the dishwasher will not run. [4]
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Cause: heating error. Troubleshooting: cycle power. If the error code returns, schedule service.
Read the supporting manualF4E2 says heating system. The wording differs, but Maytag prescribes the same reset and the same service step for both.
Read the supporting manualNot by this page. F3E2 is the neighboring code that names a thermistor or OWI sensor.
Read the supporting manualThe page does not forbid it. If the code returns after a reset, stop and book a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12626 / PH 12626 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 15079 / PH 15079 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12625 / PH 12625 (dishwasher)
Manufacturer document
Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)
W10401489A (1/12); printed page numbers; retailer copy / printed p11, “Blinking lights” row
Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Source: Product Help PH 12626, with the F4E2 and F3E2 pages.
Maytag does not define it beyond the cause line.
The page does not say so. It says heating error.
Nothing, and it is the only step Maytag lists.
It helps, though the page does not ask for it.
Maytag codes, symptoms, parts and service
Maytag Product Help prints F4E2 as “Potential Cause: Heating System.” Cycle power for 30 seconds, and schedule service if the code comes back. F4E3 is a neighboring page worded “Heating Error.”
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.