What it means
Maytag Product Help prints F2E2 as “Potential Cause: Main Control Communication Error,” the same line it uses for F1E2. Cycle power for 30 seconds and schedule service if F2E2 returns.
Maytag dishwasher F2E2 / Control board
Maytag Product Help prints F2E2 as “Potential Cause: Main Control Communication Error,” the same line it uses for F1E2. Cycle power for 30 seconds and schedule service if F2E2 returns.
Also printed as F2E2
Maytag Product Help prints F2E2 as “Potential Cause: Main Control Communication Error,” the same line it uses for F1E2. Cycle power for 30 seconds and schedule service if F2E2 returns.
Switch off power and the water supply before opening anything, and wipe up spills so nobody slips.
F2E2 returns after the 30-second power cycle.
Your Maytag to-do list, saved here on this device

Unplug the dishwasher for 30 seconds, or turn its breaker off for 30 seconds if it is hard wired, then restore power.

Run a short cycle after the reset and watch whether F2E2 returns before the first fill.

F2E1 names a stuck key; confirm nothing presses the panel before you decide it is a communication problem.

F2E2 is two flashes, a pause of about 1 to 2 seconds, then two more, with about 5 seconds before the pattern repeats. [3]

Maytag's Product Help names no model range for this code.
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
It gives one cause, a main control communication error, one troubleshooting step, cycle power, and the usual line to schedule service if the code returns.
Read the supporting manualF2E1 names a stuck key or console error. F2E2 does not mention the keys; it says the main control had a communication error.
Read the supporting manualThe cause line is identical, so the remedy is too. They remain separate entries and we keep them on separate pages.
Read the supporting manualThe retailer-copy instructions print no F-E code. They say that if the Clean light or other lights blink and the dishwasher will not run, call for service.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12624 / PH 12624 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 15081 / PH 15081 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 15082 / PH 15082 (dishwasher)
Manufacturer document
Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)
W10401489A (1/12); printed page numbers; retailer copy / printed p11, “Blinking lights” row
Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Source: Product Help PH 12624, with the F1E2 and F2E1 pages.
Maytag gives no severity. It treats it as a communication error to be power-cycled first.
The page says main control communication error; it does not tell you to replace anything.
No water step is printed for F2E2.
30 seconds with power disconnected.
Maytag codes, symptoms, parts and service
Maytag Product Help prints F2E1 as “Potential Cause: Stuck Key oe Console Error,” typo included. Cycle power for 30 seconds, and book a visit if F2E1 comes back. The only key-related check is that nothing is pressing the console.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.