What it means
Maytag Product Help prints F4E2 as “Potential Cause: Heating System.” Cycle power for 30 seconds, and schedule service if the code comes back. F4E3 is a neighboring page worded “Heating Error.”
Maytag dishwasher F4E2 / Heating
Maytag Product Help prints F4E2 as “Potential Cause: Heating System.” Cycle power for 30 seconds, and schedule service if the code comes back. F4E3 is a neighboring page worded “Heating Error.”
Also printed as F4E2
Maytag Product Help prints F4E2 as “Potential Cause: Heating System.” Cycle power for 30 seconds, and schedule service if the code comes back. F4E3 is a neighboring page worded “Heating Error.”
Switch off power and the water supply before opening anything, and wipe up spills so nobody slips.
The code is back once the 30-second power cycle is done.
Your Maytag to-do list, saved here on this device

Unplug the dishwasher for 30 seconds, or turn its breaker off for 30 seconds if it is hard wired, then restore power.

The page names the heating system. Let the tub and door cool before you open the dishwasher.

Note whether the water was ever hot or whether the code appeared at start. Tell us when you book.

The page gives no test cycle. One restart after the reset is enough to learn whether the code returns.
The retailer-copy manual says that if the Clean light or any other light blinks and the dishwasher will not run, call for service. [4]
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The cause line reads “Heating System.” The troubleshooting line is cycle power, then schedule service if the error code returns.
Read the supporting manualF4E3 is worded “Potential Cause: Heating Error.” Both end with cycle power and service; the pages do not say how a heating system and a heating error differ.
Read the supporting manualF3E2 names a thermistor or OWI sensor. F4E2 names the heating system as a whole and no sensor.
Read the supporting manualA hot tub or element is a burn risk, and the page offers no home test. A technician measures the heating circuit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 15079 / PH 15079 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12626 / PH 12626 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12625 / PH 12625 (dishwasher)
Manufacturer document
Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)
W10401489A (1/12); printed page numbers; retailer copy / printed p11, “Blinking lights” row
Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Source: Product Help PH 15079, with the F4E3 and F3E2 pages.
The page says heating system, which is wider than a single heater part.
Maytag does not say. After the power cycle, one test cycle is reasonable; stop if the code returns.
The page does not mention incoming water temperature.
They are adjacent codes with the same remedy and slightly different wording.
Maytag codes, symptoms, parts and service
Maytag Product Help prints F2E2 as “Potential Cause: Main Control Communication Error,” the same line it uses for F1E2. Cycle power for 30 seconds and schedule service if F2E2 returns.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.