What it means
Maytag Product Help prints F2E1 as “Potential Cause: Stuck Key oe Console Error,” typo included. Cycle power for 30 seconds, and book a visit if F2E1 comes back. The only key-related check is that nothing is pressing the console.
Maytag dishwasher F2E1 / User interface
Maytag Product Help prints F2E1 as “Potential Cause: Stuck Key oe Console Error,” typo included. Cycle power for 30 seconds, and book a visit if F2E1 comes back. The only key-related check is that nothing is pressing the console.
Also printed as F2E1
Maytag Product Help prints F2E1 as “Potential Cause: Stuck Key oe Console Error,” typo included. Cycle power for 30 seconds, and book a visit if F2E1 comes back. The only key-related check is that nothing is pressing the console.
Switch off power and the water supply before opening anything, and wipe up spills so nobody slips.
F2E1 returns after the 30-second power cycle.
Your Maytag to-do list, saved here on this device

Check that nothing rests on the control panel and no button looks stuck. The page names a stuck key as the first possible cause.

Unplug the dishwasher for 30 seconds, or turn its breaker off for 30 seconds if it is hard wired, then restore power.

Leave the console alone for the full 30 seconds so a held key is not mistaken for new input.

If the code is gone, start a short cycle and watch the first minute.
If the Clean light or other lights blink and the dishwasher will not run, the retailer-copy manual says to call for service. [3]
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The cause line reads “Stuck Key oe Console Error”; the troubleshooting line is cycle power, and the page ends with scheduling service if the error returns.
Read the supporting manualThe page prints “oe” where “or” is clearly meant. We quote the line as printed so you can match it to the page.
Read the supporting manualF1E2 is a main control communication error with the same remedy. F2E1 is the code that points at the keys or console, so a pressed key is the first thing to rule out.
Read the supporting manualCount the first group of flashes as the F number and the second as the E number, with a pause of about 1 to 2 seconds between and about 5 seconds before it repeats. F2E1 is two flashes, a pause, one flash.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 15082 / PH 15082 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 15081 / PH 15081 (dishwasher)
Manufacturer document
Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)
W10401489A (1/12); printed page numbers; retailer copy / printed p11, “Blinking lights” row
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-08-31; PH 15083 / PH 15083 (dishwasher)
Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Source: Product Help PH 15082, with the F1E2 page and the Reading error codes page.
Yes, it is the first cause on the page. A key held down looks like a console error to the dishwasher.
Maytag prints no cleaning step for it. The remedy is the 30-second power cycle.
The page does not say. If it will not start a cycle, stop using it and tell us.
You cannot from the page. If the panel is clear and the code returns, book a visit.
Maytag codes, symptoms, parts and service
Maytag Product Help gives F1E2 one line: “Potential Cause: Main Control Communication Error.” Cycle power for 30 seconds. If the code returns, schedule service. F1E1 and F2E2 are different pages with different wording.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.