Maytag dishwasher F1E2 / Control board

Maytag dishwasher
error code F1E2

Dishwasher / display reference

Maytag Product Help gives F1E2 one line: “Potential Cause: Main Control Communication Error.” Cycle power for 30 seconds. If the code returns, schedule service. F1E1 and F2E2 are different pages with different wording.

Also printed as F1E2

Last reviewed

Dishwasher / display reference
Meaning
Maytag Product Help gives F1E2 one line: “Potential Cause: Main Control Communication Error.” Cycle power for 30 seconds. If the code returns, schedule service. F1E1 and F2E2 are different pages with different wording.
Who handles it
Reset, then book
Source
F1E2- Dishwasher - Product Help | Maytag

What Maytag dishwasher F1E2 means.

What it means

Maytag Product Help gives F1E2 one line: “Potential Cause: Main Control Communication Error.” Cycle power for 30 seconds. If the code returns, schedule service. F1E1 and F2E2 are different pages with different wording.

What you can safely check

Close the water valve and the breaker before any panel comes off.

When to call a technician

F1E2 returns after the 30-second power cycle.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag dishwasher F1E2: Dishwasher door open with the inner panel removed, exposing the green control board and wire harness, an unplugged cord, screwdriver and pliers on a towel.
    Illustration. Follow your model’s instructions.
    Before you begin

    Power-cycle for 30 seconds

    Unplug the dishwasher for 30 seconds, or turn its breaker off for 30 seconds if it is hard wired, then restore power.

  2. Dishwashers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Start a short cycle

    After the reset, start a cycle and see whether F1E2 comes back before the tub fills.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Read the lights if there is no display

    On flashing-light models, count the first group of flashes as the F number, wait the 1 to 2 second pause, then count the second group as the E number. F1E2 is one flash, a pause, then two flashes. [5]

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Note any other lights

    The retailer-copy manual says that if the Clean light or any other light blinks and the dishwasher will not run, you will need to call for service. [4]

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Have the model number ready

    The label sits on the door edge or inside the tub. Product Help lists no models, so we need yours.

Does F1E2 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

The control and its wiring.

Conceptual dishwasher sectionKeypadControl boardMotor wiringHeater wiring1234
  1. 1Keypad
  2. 2Control board
  3. 3Motor wiring
  4. 4Heater wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does Maytag say F1E2 means?

The page calls it a main control communication error and tells you to cycle power. It adds nothing about which part is to blame, and ends with scheduling service if the code comes back.

Read the supporting manual

Why is F1E2 not the same as F1E1?

F1E1 is printed as “Potential Cause: Control Module,” again with a power cycle. The two pages use different words for what may be neighboring problems, and Maytag does not rank them.

Read the supporting manual

Is F1E2 the same as F2E2?

F2E2 is worded identically, “Main Control Communication Error,” but it is its own page.

Read the supporting manual

How do I read a flashing pattern?

Product Help describes the Clean light flashing in two groups: the first set of rapid flashes is the F number, then a pause of about 1 to 2 seconds, then the E number, then about 5 seconds before it repeats.

Read the supporting manual

The manual behind the message.

Manufacturer document

F1E2- Dishwasher - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2026-06-15; PH 15081 / PH 15081 (dishwasher)

Manufacturer document

F1E1 - Dishwasher - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2026-06-15; PH 12623 / PH 12623 (dishwasher)

Manufacturer document

F2E2- Dishwasher - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2026-06-15; PH 12624 / PH 12624 (dishwasher)

Manufacturer document

Dishwasher User Instructions (W10401489A, 1/12)

Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)

W10401489A (1/12); printed page numbers; retailer copy / printed p11, “Blinking lights” row

Manufacturer document

Dishwasher Error Codes - Reading - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2026-08-31; PH 15083 / PH 15083 (dishwasher)

Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Source: Product Help PH 15081, with the F1E1 and F2E2 pages and the Reading error codes page.

Here to help

Good questions.
Clear answers.

Talk to our team
Does F1E2 mean the control board has failed?

The page says communication error with the main control. It does not say a board has failed or must be replaced.

Do I turn off the water for F1E2?

No water step is printed for this code. That instruction appears on pages for fill-valve codes such as F8E5.

How long is the power cycle?

30 seconds, whether by unplugging or by the breaker.

Why do F1E2 and F2E2 read alike?

Maytag gives both the same cause line and the same remedy.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.