What it means
Maytag's electric cooktop page links FCE4 to the wire harness connecting the cooktop user interface (touchpad) to the induction module. It does not say which one, so run the reset below and schedule a visit if the code returns.
Maytag cooktop FCE4 / User interface
Maytag's electric cooktop page links FCE4 to the wire harness connecting the cooktop user interface (touchpad) to the induction module. It does not say which one, so run the reset below and schedule a visit if the code returns.
Also printed as FCE4
Maytag's electric cooktop page links FCE4 to the wire harness connecting the cooktop user interface (touchpad) to the induction module. It does not say which one, so run the reset below and schedule a visit if the code returns.
Power off at the breaker before any panel comes off; wiring is a technician's job.
FCE4 returns, or the electric cooktop behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; wiring is a technician's job.

Record FCE4 character by character and note the product type: electric cooktop.

Cut power at the breaker for a minute, restore it, then check for FCE4.
Run the cooktop briefly after the reset and see whether FCE4 comes back.
The power control board sits inside the electric cooktop and is left to a technician.
Keep the model number close and note when FCE4 appeared and what the electric cooktop was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
The touch control is the keypad on a Maytag electric cooktop.
Read the definitionMaytag's electric cooktop page says FCE4 may come from the wire harness connecting the cooktop user interface (touchpad) to the induction module. It stops there; no test and no ranking is given.
Read the supporting manualTake the cooktop off power at the breaker for a full minute. Put it back on and give it a minute of watching; if FCE4 stays away, the reset did its job.
Read the supporting manualRead the exact display: FCE1 means the cooktop user interface (touchpad) or the wiring on the electric cooktop page, and FCE4 means the wire harness connecting the cooktop user interface (touchpad) to the induction module.
Read the supporting manualKeep the electric cooktop off until FCE4 is explained if touch controls act oddly.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-01-22; PH 12871 / PH 12871 (electric cooktop)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2022-03-24; PH 12007 / PH 12007 (electric cooktop)
Facts for FCE4 are from the electric cooktop table (PH 12871) of Maytag Product Help, checked November 2026; no model list is printed.
FCE4 is printed against the wire harness connecting the cooktop user interface (touchpad) to the induction module; the page does not narrow it down.
It is the page's first step and costs nothing. A returning FCE4 afterward means schedule us.
The list is the wire harness connecting the cooktop user interface (touchpad) to the induction module; testing on site settles it.
Tell us the model, the display wording and when FCE4 first showed up.
Maytag codes, symptoms, parts and service
Maytag's electric cooktop page links FCE1 to the cooktop user interface (touchpad) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
A Maytag electric cooktop that keeps beeping may have something on the control area, Control Lock being turned on or off, or a utensil left on an element too long. Clear and wipe the control panel first. Beeping for more than 15 minutes locks the panel and can show F1E0 on some models.
The touch control is the keypad on a Maytag electric cooktop. It is the part you touch to turn cooking areas on and set heat. Product Help calls it the user interface, touchpad or touch control module, and its F22, FC E1 and F6E0 pages point to it. The first step printed is a one-minute breaker reset.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.