What it means
The Maytag electric cooktop entry for FC LF names the left front hotplate (cooking surface/burner/element) or the wiring. Reset first, then call us in if the code keeps coming back.
Maytag cooktop FC LF / Heating
The Maytag electric cooktop entry for FC LF names the left front hotplate (cooking surface/burner/element) or the wiring. Reset first, then call us in if the code keeps coming back.
Also printed as FC LF
The Maytag electric cooktop entry for FC LF names the left front hotplate (cooking surface/burner/element) or the wiring. Reset first, then call us in if the code keeps coming back.
Turn the breaker off before you touch anything behind a panel, and leave wiring and supply connections to a technician.
FC LF returns, or the electric cooktop behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Turn the breaker off before you touch anything behind a panel, and leave wiring and supply connections to a technician.

Check that your appliance is an electric cooktop and copy FC LF exactly as the display shows it.

Leave the breaker off a whole minute before checking for FC LF again.

Once power is back, keep an eye on the cooktop for about a minute for FC LF.
Make sure pans sit flat and centered on the electric cooktop.
Keep the model number close and note when FC LF appeared and what the electric cooktop was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
Maytag Product Help prints two meanings for F12 on an electric cooktop.
Read the definitionFor FC LF the electric cooktop entry names the left front hotplate (cooking surface/burner/element) or the wiring. Nothing in it says which of them has failed.
Read the supporting manualTurn the cooktop's circuit breaker off for one minute, switch it back on, then keep an eye on the cooktop for a further minute to see whether FC LF comes back.
Read the supporting manualMaytag lists the wire harness connecting the cooktop user interface (touchpad) to the induction module against FCE4, while FC LF gets the left front hotplate (cooking surface/burner/element) or the wiring. They are neighbors in the electric cooktop list but separate entries.
Read the supporting manualTreat the area as hot and keep it clear until it has been checked. If FC LF keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-01-22; PH 12865 / PH 12865 (electric cooktop)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2022-03-24; PH 12008 / PH 12008 (electric cooktop)
Scope for FC LF: Maytag electric cooktop, PH 12865, checked November 2026. Maytag lists no models on the FC LF page.
The electric cooktop page ties FC LF to the left front hotplate (cooking surface/burner/element) or the wiring without saying which has failed.
Yes, give it the whole minute. If FC LF is still there afterward, schedule a visit.
Not from the code alone: the entry lists the left front hotplate (cooking surface/burner/element) or the wiring and stops.
The model number, what FC LF looked like, and whether the reset changed anything.
Maytag codes, symptoms, parts and service
Maytag's electric cooktop page links FCE4 to the wire harness connecting the cooktop user interface (touchpad) to the induction module. It does not say which one, so run the reset below and schedule a visit if the code returns.
A Maytag electric cooktop that keeps beeping may have something on the control area, Control Lock being turned on or off, or a utensil left on an element too long. Clear and wipe the control panel first. Beeping for more than 15 minutes locks the panel and can show F1E0 on some models.
Maytag Product Help prints two meanings for F12 on an electric cooktop. One page points to a hotplate (cooking surface, burner or element) or its wiring. Another says there is an internal communication error on the touch control module. Both give a one-minute breaker reset.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.