What it means
Maytag's range page links 1c31 to the oven control or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Maytag oven 1c31 / Control board
Maytag's range page links 1c31 to the oven control or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Also printed as 1c31
Maytag's range page links 1c31 to the oven control or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
1c31 will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

Check that your appliance is a range and copy 1c31 exactly as the display shows it.

Breaker off for one full minute, then back on, and look for 1c31.

Run the oven briefly after the reset and see whether 1c31 comes back.

Note whether the display, keys and lights of the range behave normally, or whether other odd things happen near 1c31.
Keep the model number close and note when 1c31 appeared and what the range was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
Maytag range pages for F1-7, F3 and F6 point at the control board of the oven, or the wiring to it.
Read the definitionMaytag's range page says 1c31 may come from the oven control or the wiring. It stops there; no test and no ranking is given.
Read the supporting manualTake the oven off power at the breaker for a full minute. Put it back on and give it a minute of watching; if 1c31 stays away, the reset did its job.
Read the supporting manual1c2c sits beside 1c31 on the range page and names the user interface/keypad or the wiring; the code names the oven control or the wiring.
Read the supporting manualIf the range behaves after the reset, using it is up to you; if 1c31 returns, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13695 / PH 13695 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14355 / PH 14355 (wall oven)
Facts for 1c31 are from the range table (PH 13695) of Maytag Product Help, checked November 2026; no model list is printed.
1c31 is printed against the oven control or the wiring; the page does not narrow it down.
Yes, give it the whole minute. If 1c31 is still there afterward, schedule a visit.
No. the oven control or the wiring are all candidates and the page gives no way to choose.
The model and serial numbers, the exact display for 1c31, and what the range was doing at the time.
Maytag codes, symptoms, parts and service
1c2c on your range is tied by Maytag to the user interface/keypad or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
Maytag range pages for F1-7, F3 and F6 point at the control board of the oven, or the wiring to it. F1-8 also names the keypad and its interface. The only home step printed is a one-minute breaker reset, followed by watching the oven.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.