What it means
1c2c on your range is tied by Maytag to the user interface/keypad or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Maytag oven 1c2c / User interface
1c2c on your range is tied by Maytag to the user interface/keypad or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Also printed as 1c2c
1c2c on your range is tied by Maytag to the user interface/keypad or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Turn the breaker off before you touch anything behind a panel.
1c2c will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Turn the breaker off before you touch anything behind a panel. If you smell gas, leave the house and call your gas utility from outside.

Record 1c2c character by character and note the product type: range.

Cut power at the breaker for a minute, restore it, then check for 1c2c.

Give the oven a minute on screen after the reset; a returning 1c2c means schedule a visit.

Press each key on the range one at a time and note any that do nothing, beep alone or stick.
Write down the model and serial numbers and the exact 1c2c wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
Maytag range pages for F1-7, F3 and F6 point at the control board of the oven, or the wiring to it.
Read the definition1c2c is printed against the user interface/keypad or the wiring. Maytag words it as a possible problem, not a finding.
Read the supporting manualTake the oven off power at the breaker for a full minute. Put it back on and give it a minute of watching; if 1c2c stays away, the reset did its job.
Read the supporting manual1c1c carries the same parts list as 1c2c on the range page. The reset is the same, only the code differs.
Read the supporting manualA keypad problem is about control. If keys seem to press themselves, switch the range off at the breaker.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13694 / PH 13694 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14354 / PH 14354 (wall oven)
Scope for 1c2c: Maytag range, PH 13694, checked November 2026. Maytag lists no models on the 1c2c page.
The range page ties 1c2c to the user interface/keypad or the wiring without saying which has failed.
Yes, give it the whole minute. If 1c2c is still there afterward, schedule a visit.
Maytag names the user interface/keypad or the wiring. Which one failed is for a technician with a meter to decide.
Model and serial numbers plus a note of what happened when 1c2c appeared.
Maytag codes, symptoms, parts and service
1c1c on a range means Maytag suspects the user interface/keypad or the wiring. Begin with the reset; if the code is back afterward, book a technician.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
Maytag range pages for F1-7, F3 and F6 point at the control board of the oven, or the wiring to it. F1-8 also names the keypad and its interface. The only home step printed is a one-minute breaker reset, followed by watching the oven.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.