What it means
For a vent hood showing the code, Maytag prints “After 30 hours of fan operation, the display will show 'F' when the fan is active.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Maytag hood F / Fan and airflow
For a vent hood showing the code, Maytag prints “After 30 hours of fan operation, the display will show 'F' when the fan is active.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Also printed as F
For a vent hood showing the code, Maytag prints “After 30 hours of fan operation, the display will show 'F' when the fan is active.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
On a vent hood showing F, Power off at the breaker before any panel comes off; wiring is a technician's job.
F will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

On a vent hood showing F, Power off at the breaker before any panel comes off; wiring is a technician's job.

Check that your appliance is a vent hood and copy F exactly as the display shows it.

No reset is printed here; note the behavior of the vent hood around F instead.
Write down the model and serial numbers and the exact F wording before you call.
Note when F appears: at start, mid-cycle or after a power cut.
Note the model and the moment F showed up; both help us plan.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag vent hood, the display shows F after 30 hours of fan operation, which means the grease filters need washing.
Read the definitionMaytag's vent hood page gives F a single line: “After 30 hours of fan operation, the display will show 'F' when the fan is active.” It adds nothing about cause.
Read the supporting manualMaytag's page for F gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the vent hood shows.
Read the supporting manualC is a neighbor of F, not a synonym. The reset may overlap; the text does not.
Read the supporting manualUse the vent hood if it behaves normally; stop if there are odd noises, smells or heat.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-02-17; PH 14653 / PH 14653 (vent hood)
Facts for the code are from the vent hood table (PH 14653) of Maytag Product Help, checked November 2026; no model list is printed.
The vent hood page reads “After 30 hours of fan operation, the display will show 'F' when the fan is active.” It prints nothing more about cause.
The page prints none. Write down what you see and schedule a visit if F keeps appearing.
Nothing about replacing parts is printed for F.
Model and serial numbers plus a note of what happened when F appeared.
Maytag codes, symptoms, parts and service
For a vent hood showing C, Maytag prints “After 120 hours of fan operation, the display will show 'C' when the fan is active.” Nothing else is printed, so schedule a visit if it repeats.
On a Maytag vent hood, F means the grease filter has hit 30 hours of fan operation and C means the charcoal filter has hit 120 hours. They are cleaning reminders, not breakdowns. Wash the filter, then hold FAN for 3 seconds to clear the reminder.
On a Maytag vent hood, the display shows F after 30 hours of fan operation, which means the grease filters need washing. Product Help says to wash the metal filter in the dishwasher or hot detergent solution, let it dry thoroughly, then clear the alert by holding FAN for 3 seconds.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.