What it means
E1 on a Maytag commercial-grade residential dryer is explained as “Power unit down by turning off the circuit breaker(s) for 5 minutes.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Maytag dryer E1 / Reset only
E1 on a Maytag commercial-grade residential dryer is explained as “Power unit down by turning off the circuit breaker(s) for 5 minutes.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Also printed as E1
E1 on a Maytag commercial-grade residential dryer is explained as “Power unit down by turning off the circuit breaker(s) for 5 minutes.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Power off before any panel comes off; lint and burnt smells mean stop and leave the dryer off.
E1 repeats after the reset.
Your Maytag to-do list, saved here on this device

Power off before any panel comes off; lint and burnt smells mean stop and leave the dryer off.

Match the label on your appliance to the commercial-grade residential dryer list before you rely on the wording for E1.

Wait five minutes without power before you check for E1 again.

Give the dryer a minute on screen after the reset; a returning E1 means schedule a visit.

Check your model manual for what E1 means before treating it as a breakdown.
Write down the model and serial numbers and the exact E1 wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Maytag's commercial-grade residential dryer page gives E1 a single line: “Power unit down by turning off the circuit breaker(s) for 5 minutes.” It adds nothing about cause.
Read the supporting manualCut power to the dryer for five minutes at the breaker or by cycling power as the page says, then restore it and see whether E1 comes back.
Read the supporting manualThe commercial-grade residential dryer list prints PF next to E1, but with a different line. Look up the one on your display.
Read the supporting manualUse the commercial-grade residential dryer if it behaves normally; stop if there are odd noises, smells or heat. Never open a panel on the commercial-grade residential dryer yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-07-28; PH 11806 / PH 11806 (commercial-grade residential dryer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2023-12-07; PH 12780 / PH 12780 (dryer)
E1 comes from Maytag Product Help (PH 11806) for the commercial-grade residential dryer, read in November 2026; the E1 entry names no models.
Maytag's wording is “Power unit down by turning off the circuit breaker(s) for 5 minutes.” That is the whole entry.
It may. Cut power for the full five minutes, restore it and watch. If E1 returns, schedule a visit.
Maytag names no part here. Read the message and follow the steps.
The model and serial numbers, the exact display for E1, and what the commercial-grade residential dryer was doing at the time.
Maytag codes, symptoms, parts and service
On a commercial-grade residential dryer, the entry for PF says “A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure.” Switch the breaker off for a minute, then back on; schedule a visit if the code is still there.
A Maytag dryer that does nothing is usually a power, lock or latch issue before it is a broken part. An electric dryer draws on two breakers or fuses and needs 240 volts, the Control Lock may be on, and the door may look shut without latching. Check these, then book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.