Start from the symptom
Maytag dryer burning smell.
A new Maytag dryer can give off a semi-burning or oily smell, and Product Help says to run it empty for about 15 minutes. Paint fumes in the room and a damp load left sitting are the other named causes. A hot, scorched smell that fits none of these means switch it off and arrange a visit.

Start with safe observations.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Is the dryer new?
A new gas or electric dryer may smell semi-burnt or oily. Run it with no clothes for about 15 minutes.
- 2
Paint, stain or varnish nearby
The dryer pulls in room air, so fumes end up on the load. Ventilate the area, then rewash and dry the load. Avoid running the dryer during refinishing work.
- 3
Damp clothes left sitting
A wet load left in the washer or dryer grows mildew and smells. Rewash and dry it, and take loads out promptly when the cycle ends.
- 4
Clean the drum
Product Help points to its drum cleaning page for odors that remain.
- 5
Lint screen and vent
If the display shows F4E3, Maytag says the lint screen or vent is clogged, or the vent is crushed, kinked or has too many turns. Deal with that first.
Systems a technician may investigate.
These parts tie in to the symptom. Noticing it does not prove that any single one has worn out.
Read the related care guide.

A dryer that tumbles but never warms: check the supply before the machine.
When a Maytag electric dryer tumbles with no heat, check the household supply before the machine: both breakers of its 30-amp, 240-volt circuit, the power cord and the terminal screws. An L2 or F4 E4 code points the same way, and a five-minute breaker reset is the step Maytag gives. F4 E1 names the heater or its relays and uses a one-minute reset. [1][2][3][4]

A code on your dryer: vent, supply or reset?
On a Maytag dryer, group the codes by the first thing each one wants. F4 E3 and the AF or Check Vent light mean airflow: clean the lint screen and vent. F4 E4 and L2 mean the household supply: check both breakers. F1 E1, F3 E3, F4 E1 and F6 E1 mean a breaker reset. PF means the cycle was cut short by a power failure. [1][3][4][5][6][7][8]
When observation becomes a service request.
Leave internal testing to a technician.
The smell is hot or scorched and none of the causes above fit.
You smell it again after the empty run and a clean drum.
F4E3 returns after the lint screen and vent run are clear.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Maytag dryer burning smell advice. Read the manual for your own model.
- Removing Odors or Smells - Dryer - Product Help | Maytag
- F4 E3 - Error Code - Dryer - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
Should a brand-new dryer smell scorched?
Maytag says a new gas or electric dryer can give off a semi-burning or oily smell, and to run it empty for about 15 minutes. If it does not fade, book a technician.
Why do my clean clothes smell of paint?
The dryer draws in the surrounding room air, so fumes from fresh paint, stain or varnish end up on the load. Ventilate, wait until the smell clears, then rewash and dry.
Could a blocked vent cause a burning smell?
Product Help does not tie the two together. It does say F4E3 on a dryer means a clogged lint screen or vent, so clear those, since restricted airflow is not good for a hard-working dryer.
What should I do if the smell is strong?
Stop the dryer, leave it unplugged, and book a technician. The causes Maytag lists are mild and fade, so a hot or scorched smell is outside them.
Maytag codes, symptoms, parts and service
From the message to what you do next.
F4E3
F4E3 on a Maytag commercial-grade residential dryer is explained as “An F4 E3 (Restricted Air Flow) error code indicates that the lint screen or vent is clogged; the vent may be...” No reset is printed for it, so schedule a visit if it keeps appearing.
Maytag dryer will not start
A Maytag dryer that does nothing is usually a power, lock or latch issue before it is a broken part. An electric dryer draws on two breakers or fuses and needs 240 volts, the Control Lock may be on, and the door may look shut without latching. Check these, then book a technician.
Dryer lint screen and exhaust vent (F4E3, AF)
Long dry times on a Maytag dryer often trace to airflow. F4E3, AF and Check Vent all say the lint screen or vent is clogged, crushed, kinked or has too many turns. Product Help wants the lint screen cleaned after every use and the home venting every one to two years.
Dryer repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.
