What it means
The Maytag page for F50 on a commercial-grade residential dryer states “Power unit down by turning off the circuit breaker(s) for 5 minutes.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Maytag dryer F50 / Reset only
The Maytag page for F50 on a commercial-grade residential dryer states “Power unit down by turning off the circuit breaker(s) for 5 minutes.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Also printed as F50
The Maytag page for F50 on a commercial-grade residential dryer states “Power unit down by turning off the circuit breaker(s) for 5 minutes.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Unplug the dryer or switch off its breaker before opening any panel, clean lint regularly, and if you smell gas leave the house and call your gas utility.
F50 will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Unplug the dryer or switch off its breaker before opening any panel, clean lint regularly, and if you smell gas leave the house and call your gas utility.

Check that your appliance is a commercial-grade residential dryer and copy F50 exactly as the display shows it.

Wait five minutes without power before you check for F50 again.

Once power is back, keep an eye on the dryer for about a minute for F50.

Write down the exact words or symbols the commercial-grade residential dryer shows before you do anything.
Write down the model and serial numbers and the exact F50 wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
F50 is covered by this wording on the commercial-grade residential dryer page: “Power unit down by turning off the circuit breaker(s) for 5 minutes.”
Read the supporting manualLeave the dryer off power for five full minutes, switch it back on, and check the display for F50.
Read the supporting manualThe commercial-grade residential dryer list prints F31 next to F50, but with a different line. Look up the one on your display.
Read the supporting manualUse the commercial-grade residential dryer if it behaves normally; stop if there are odd noises, smells or heat. Never open a panel on the commercial-grade residential dryer yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-07-28; PH 11829 / PH 11829 (commercial-grade residential dryer)
Facts for F50 are from the commercial-grade residential dryer table (PH 11829) of Maytag Product Help, checked November 2026; no model list is printed.
The commercial-grade residential dryer page reads “Power unit down by turning off the circuit breaker(s) for 5 minutes.” It prints nothing more about cause.
Wait the whole five minutes, not less. If F50 persists, a technician should look.
Not by itself; the page stops at the line it prints.
The model and serial numbers, the exact display for F50, and what the commercial-grade residential dryer was doing at the time.
Maytag codes, symptoms, parts and service
For a commercial-grade residential dryer showing F31, Maytag prints “An L2 (Low or No Line Voltage) Error code indicates that there may be a problem with your home power supply...” Try the one-minute breaker reset, and schedule a visit if the code returns.
A Maytag dryer that does nothing is usually a power, lock or latch issue before it is a broken part. An electric dryer draws on two breakers or fuses and needs 240 volts, the Control Lock may be on, and the door may look shut without latching. Check these, then book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.